diff --git a/src/Mod/Arch/Resources/translations/Arch.ts b/src/Mod/Arch/Resources/translations/Arch.ts
index 6fcd7ef471..b711f69891 100644
--- a/src/Mod/Arch/Resources/translations/Arch.ts
+++ b/src/Mod/Arch/Resources/translations/Arch.ts
@@ -4459,6 +4459,11 @@ If Run = 0 then the run is calculated so that the height is the same as the rela
Custom Rebar
+
+
+ Creates a Reinforcement bar from the selected face of solid object and/or a sketch
+
+ Creates a Reinforcement bar from the selected face of a structural object
diff --git a/src/Mod/Draft/Resources/translations/Draft.ts b/src/Mod/Draft/Resources/translations/Draft.ts
index bb7a3a51ba..0634cca949 100644
--- a/src/Mod/Draft/Resources/translations/Draft.ts
+++ b/src/Mod/Draft/Resources/translations/Draft.ts
@@ -635,11 +635,6 @@ This property is read-only, as the number depends on the points contained within
Area of this object
-
-
- The shape of this object
-
- The base object used by this object
@@ -650,6 +645,11 @@ This property is read-only, as the number depends on the points contained within
The PAT file used by this object
+
+
+ The shape of this object
+
+ The pattern name used by this object
diff --git a/src/Mod/Path/Gui/Resources/translations/Path.ts b/src/Mod/Path/Gui/Resources/translations/Path.ts
index b7817ff284..e812236394 100644
--- a/src/Mod/Path/Gui/Resources/translations/Path.ts
+++ b/src/Mod/Path/Gui/Resources/translations/Path.ts
@@ -713,16 +713,6 @@
Expression used for StepDown of new operations.
-
-
- The direction that the toolpath should go around the part ClockWise (CW) or CounterClockWise (CCW)
-
-
-
-
- Extra offset to apply to the operation. Direction is operation dependent.
-
- Start pocketing at center or boundary
@@ -733,6 +723,16 @@
Percent of cutter diameter to step over on each pass
+
+
+ The direction that the toolpath should go around the part ClockWise (CW) or CounterClockWise (CCW)
+
+
+
+
+ Extra offset to apply to the operation. Direction is operation dependent.
+
+ Angle of the zigzag pattern
@@ -1568,6 +1568,16 @@
PathJob
+
+
+ Unsupported stock object %s
+
+
+
+
+ Unsupported stock type %s (%d)
+
+ Stock not from Base bound box!
@@ -1583,16 +1593,6 @@
Stock not a cylinder!
-
-
- Unsupported stock object %s
-
-
-
-
- Unsupported stock type %s (%d)
-
- The NC output file for this project
@@ -1737,14 +1737,14 @@
-
- FinalDepth cannot be modified for this operation.
-If it is necessary to set the FinalDepth manually please select a different operation.
+
+ Heights
-
- Heights
+
+ FinalDepth cannot be modified for this operation.
+If it is necessary to set the FinalDepth manually please select a different operation.
@@ -3389,6 +3389,36 @@ Aborting op creation
Create Job
+
+
+ Warning
+
+
+
+
+ Please add one.
+
+
+
+
+ Ok
+
+
+
+
+ Add
+
+
+
+
+ This job has no base model.
+
+
+
+
+ This job has no tool.
+
+ Fixture