==========================
* Enable to select any GeomTrimmedCurve (any arc supported by the Sketcher), as well as B-Splines.
* Use Edit Markers to provide visualisation of the cutting position and cut segment end point before trimming.
* Reject trimming Internal aligned geometry (internals of complex geometries such as ellipses or hyperbolas)
======================================
* Refactor the code for all GeomTrimmedCurve and non-periodic BSplines in a single block, adding
support for arcs of hyperbola, parabola and B-Splines.
* Refactor the code for periodic curves (circle, ellipse) in a single block, adding support for
periodic B-Splines.
* Add support for trimming limited by external geometry
* Trim deletes a geometry if intersections are detected and nothing would be left after trimming
* Trim deletes a geometry if no intersection are detected
Bonus:
* Function addConstraint moving the constraint instead of cloning it again
* SketchObject::seekTrimPoints as a wrapper of Part2DObject::seekTrimPoints providing
a correct handling of GeoId indices.
* Helper functions addConstraint/createconstraint to create new constraints and move them
into the Constraint property
* New getGeometry with templated return type defaulting to Part::Geometry.
=====================================================
New Coin Marker layer intended to temporarely highlight sections of the 3D View for information purposes.
Independent from the actual redrawing of the geometry and constraints.
============================================================================================
On creation of a constraint from the UI (toolbar/menu):
1. if a PointOnObject constraint preexisted the addition of an
edge-to-edge tangency, substitute it with a point-to-edge tangency.
2. if an edge-to-edge tangency preexisted, addition of a PointOnObject
results in a substitution of the edge-to-edge tangency with an edge-to-curve
tangency.
Bonus:
- Refactor of this with preexisting coincident+tangent substitution.
- Activate both substitutions in continuous constraint addition mode.
================================
Calls to:
Gui::BitmapFactory().pixmapFromSvg(type.toLatin1().data(),QSizeF(edit->constraintIconSize,edit->constraintIconSize));
are expensive and the scaled pixmap is heavily reused.
Solution is to cache the icon.
The existing icon for the sketcher constraint for "constraint block" is easily confused with the icon for the diameter constraint. A small modification to add a 2nd cross bar will visually distinguish it.
=============================================================================
THIS IS A WORK-AROUND NOT TO DELAY 0.19 RELEASE
depsAreTouched is not returning true in this case:
https://forum.freecadweb.org/viewtopic.php?f=3&t=55633&p=481061#p478477
It appears related to a drastic change in how dependencies are calculated, see:
https://forum.freecadweb.org/viewtopic.php?f=3&t=55633&p=481061#p481061
This is NOT the solution, as there is no point in systematically executing the ExpressionEngine
on every dimensional constraint change. Just a quick fix to avoid clearly unwanted behaviour in
absence of time to actually fix the root cause.
Coverity warnings fixed:
CID 129530 (#1 of 1): Uninitialized scalar field (UNINIT_CTOR)
2. uninit_member: Non-static class member pixelScalingFactor is not initialized in this constructor nor in any functions that it calls.
===========================================================================================================
OCCT forces weights of non-rationa Bsplines to be 1.0
In the presence of non-unitary weight constraints, the weight representation (constraint) has a different radius
than the circle.
This commit fixes this behaviour, by forcing the circle to match the weight constraint.
The information layer still reports OCCT weights being 1.0, but the visual artifact is fixed.
====================================================================
When the ellipse to be projected and the sketch plane are parallel, the original code
by shermelin provided for a translation of the original ellipse, which would be the best solution
if it weren't because the Sketcher, internally, works under the assumption of a normal vector to the
sketcher plane being (0,0,1). If the original ellipse is parallel to the sketch plane, but the sketch
plane is not the XY plane, the copy and translation would result in a ellipse not in the XY plane of the
Sketcher. Then the sketcher internals will not properly consider its dimensions.
The solution applied here is to default to the general method for non-parallel planes.
It solves:
https://forum.freecadweb.org/viewtopic.php?f=3&t=55284#p477522
========================================================
Users chennes and hyarion made me aware of this covereity issue:
Fixes Coverity: geoit can be end() when dereferenced
https://github.com/FreeCAD/FreeCAD/pull/4429/files#
When analysing the block where the dereferrencing appears, it
appears that it is a left-over that no longer makes sense:
- The algorithm classifies block constraints into those that are
not affected by any other driving constraint and those that are
affected by other driving constraints.
- The offending block deals with internal aligned geometry, thus
per definition has a driving internal alignment constraint, for which
the previous block already set the need of post-analysis.
- No matter what, the geometries, the complex one and the internal one
will have at least the driving internal alignment constraint, so they
cannot become "not affected by any other driving constraint".
- If the geometry had a block constraint on it, it was already added for
post-analysis in the previous block. If it did not have one block constraint,
the fact that it is internal aligned geometry is an irrelevant consideration.
Probably there was a point during development when this made sense, but with
the current post-analysis, it does not appear to make sense anymore. So the
block was removed.
This commit adds a unit test for blocked geometry (new block constraint).
Fixes Coverity issue:
CID 316539 (#1 of 1): Uninitialized scalar field (UNINIT_CTOR)
uninit_member: Non-static class member lastHasPartialRedundancies is not initialized in this constructor nor in any functions that it calls.
=================================================
Knot position is not calculated by the solver, but by OCCT when updating the
b-spline to conform to given pole positions, as mandated by the solver. Before
this commit, all constraints driving and non-driving operating on the knots required
and extra solve (from advanced solver dialog, or from the Python console), or a recompute
to be recomputed.
This commit introduces transparently re-solving at Sketch.cpp level if B-Splines are present,
so that when the Sketcher mandated solve returns, the geometry is fully solved.
========================================
The geometry state stored in the geometryFacade is modified following a mutable model
(without setting the Geometry property on Constraint change), in order to avoid coupling
the addition/removal of a constraint with a change of the Geometry Property.
This design decision however interferes with the ability of the Geometry property to restore
the correct geometry state upon redo/undo.
While such a situation is rare in the case of Internal Alignment geometry, because constraint
addition/removal is performed with the corresponding geometry addition/removal (within the same
transaction. That is not the case with the Block constraint (or another future general case where
the geometry state may be applied).
This commit leverages the synchronisation mechanism already in use for non-properties (e.g. external geometry or
vertex indices) to check and synchronise geometry state upon undo/redo and restore.
Bonus:
- addGeometryState is refactored to separate the checking logic from the setting logic.
Currently the sketch fillet tool deletes any constraints associated with
the two lines to be filleted. By leaving a vertex at the intersection,
we can instead preserve most constraints in reasonable ways.
Sketch fillet horizontal and vertical point-to-point constraint support
Also better future compatibility for point constraints, and some minor tweaks.
